Adaptors, Sensors & Power Packs

Mitsubishi Electric`s advanced interface technologies, room sensors and power options allow you flexibility to tailor your heating and cooling solutions.

MAC-558IF-E
The award winning MAC-558IF-E Wi-Fi Control Adaptor connects discreetly to your heat pump’s control board and should only be installed by an authorised installer. The MAC-558IF-E Wi-Fi Control Adaptor is available on Mitsubishi Electric High Wall, Floor Mounted, and Ducted Heat Pumps, and can either be purchased as an optional upgrade at time of purchase, or retrofitted to an existing Mitsubishi Electric model.
PAC-YG10HA-E
Input/Output Adapter
PAC-YG10HA-E
Input/Output Adapter. Provides control for fresh air fan start-up and emergency fire stop. Connects to a centralised and web controller.
PAC-YG60
Pulse Input Control module. Provides an analogue input for: watt hour meter with pulse transmitter, etc. Connects to a Centralised and Web Central Controller.
PAC-YG63
Analogue Input Control module. Provides an analogue input for: temperature & humidity sensors, etc. Connects to a Centralised and Web Central Controller.
PAC-YG66
This interface is a digital input and output control module. It provides an analogue input for ventilation fans, lighting etc. Connects to a centralised and web central controller.
PAC-SF81MA-E
Interface Unit
PAC-SF81MA-E
Interface to enable P-Series units to be operated by a Central or Schedule Controller. When the P-Series indoor is connected to a SUZ outdoor use a MAC-399IF-E .The interface is installed on each outdoor unit for: PUHZ-RP71/100/125/140/200/250 and wired to a Central or Schedule Controller
PAC-SC51KUA
Power Pack
PAC-SC51KUA-J
PAC-SC51KUA-J Power Pack. This unit supplies DC power to controller (AG-150A).
MAC-397IF-E
MA and Contact Terminal Interface for the PAR-21MAA, PAR-30MAA and MAC-821SC-E Controllers when connecting to: MSZ-GE/FB~VA, MSZ-FB/MFZ-FB~VAH, MFZ-KA~VA or SLZ-KA~VAL indoor units. Older models may be connectable, refer to manual.
PAC-SF40RM-E
Remote Operation Adapter. Plugs into the Indoor PCB (PEA-RP, PLA-RP, PCA-RP, PKA-RP). Provides a Non Voltage A-contact for External Input On/Off Control, Emergency Output for Faults, Run Output for Operation.
PAC-SE41TS-E
Remote Sensor
PAC-SE41TS-E
Remote Sensor. This is fitted in place of the existing Return Air Sensor to provide Room Sensing. Flush mounted sensor housing.
PAC-SE55RA-E
3-Pin Timer Adapter
PAC-SE55RA-E
3-Pin Timer Adapter. Plugs into the Indoor Unit PCB. Provides On/Off Input; Low Voltage Pulse or Level Contact Start and Stop signal to each indoor unit. For connection to an External Building Time Clock* etc. (*Supplied by Electrician)
MAC-333IF-E
Interface Unit
MAC-333IF-E
MA, M-NET and Contact Terminal Interface. Has remote on/off, prohibit/permit control and run/error outputs - all outputs require an independent external 12VDC power supply. Used to connect PAR-21 / PAR-31 to; MSZ-GE/FB/EF, MFZ-KA/FB & SLZ-KA~VAL indoor units or a Central / Schedule Controller to each indoor unit connected to a M or S-Series outdoor unit.
MAC-568IF-E
Wi-Fi Interface
MAC-568IF-E
The award-winning MAC-568IF-E Wi-Fi Interface connects discreetly to your heat pump’s control board and should only be installed by an authorised installer. The MAC-568IF-E Wi-Fi Interface is available on Mitsubishi Electric High Wall, Floor Mounted, and Ducted Heat Pumps, and can either be purchased as an optional upgrade at time of purchase, or retrofitted to an existing Mitsubishi Electric model.
MAC-559IF-E
Wi-Fi Interface
MAC-559IF-E
The award winning MAC-559IF-E Wi-Fi Interface connects discreetly to your heat pump’s control board and should only be installed by an authorised installer. The MAC-559IF-E Wi-Fi Interface is available on Mitsubishi Electric High Wall, Floor Mounted, and Ducted Heat Pumps, and can either be purchased as an optional upgrade at time of purchase, or retrofitted to an existing Mitsubishi Electric model.
Adaptors, Sensors & Power Packs